Monday, November 28, 2011

Automatic Trap Primer Valve - Precision Plumbing Products

This innovative trap priming system automatically primes up to four floor drain traps using our patented water distributsion system. The PRIME-RITE requires no adjustment but must be installed on a cold water line of 1-1/2" (38mm) diameter or less. The priming valve is automatically activated when it senses a pressure drop of 5 to 10 P.S.I.G. (35 to 70 kpa). The valve's operating range is 35 to 75 P.S.I.G. (245 to 535 kpa). All PR-500 Valves include integral vacuum breaker parts.

The PR-500 Prime-rite trap primer is an easy to use and install product. It has a ½” inch inlet and outlet to connect to most normal lines and can be installed on cold water lines 1-1/2” diameters or less. The PR-500 also adjusts to line pressure to keep you from worrying about the trap primer when it’s in use.

PPP PR-500 Prime-rite Primer Automatic Trap Primer Valve Features:


• 1/2" inlet/outlet
• Installed on cold water lines of 1-1/2" diameter or less.
• Automatically adjusts to line pressure
• One priming valve will prime 1 to 4 floor drain traps, using the water distibution system
• Machined from CDA 360 corrosion resistant brass
• Does not contain springs, diaphrams, or plastic parts

* The priming valve must have a minimum elevation of 12 inches above the finished floor.
• CA/VT compliant

Monday, November 21, 2011

Why We Need Relief Valves

Ever wonder what would happen if a relief valve failed or was plugged? This short video on Youtube from Mythbusters shows just what can happen. These guys constructed a mock up of a 2 story house and set a 53 gallon electric water heater in what would be the basement. They plugged the relief valve and monitored the temperature and pressure from a safe distance. What happened a few minutes later will amaze and frighten you at the same time.

Monday, November 14, 2011

Domestic Hot Water

The Problem:
Waiting for Hot Water

It’s a common problem: turn on the faucet or shower for hot water, then wait for it to arrive. With a Taco Domestic Hot Water Recirculation System in place, there’s no more wait. Instant hot water!

Waiting Means Wasting
Waiting for hot water sends millions of gallons of cooled water down the drain each year. In fact, an average family of 4 wastes up to 14,000 gallons of water each year waiting for hot water.*
*Source: Dept. of Energy study.

Energy Down The Drain
Of course, all that “waiting water” contains some heat energy (BTU’s). Wasting those BTU’s and starting over with fresh, cold water requires even more heat energy. So in addition to wasting water, millions of BTU’s and energy dollars are wasted, too.

The Solution:
Install a Domestic Hot Water Recirculation System.
The Taco Plumb n’ Plug® Recirculation System is specifically designed for:
  • Instant hot water comfort
  • Water savings
  • Energy savings

How a Domestic Hot Water Recirculation System Works
A standard DHW system requires a dedicated return line from the furthest fixture back to the water heater. The return line is connected to a tee at the tank drain valve or to the tank’s cold water supply line. A Taco Plumb n’ Plug® recirculation pump with an optional Integral Flow Check (IFC) is installed on the return line and controlled by a timer or temperature aquastat. The spring-loaded IFC prevents gravity circulation during off-cycles. The timer turns on the pump at preset intervals, usually during peak use periods. An optional Aquastat operates the pump to keep hot water in the line within a set range (95°F–115°F). All supply and return lines should be insulated for maximum energy savings.


View the DHW catalog here.
 

Tuesday, November 1, 2011

View The Rebates You Qualify For Right Here!

Tuesday, October 18, 2011

The Versa-Flame by HTP

The Versa-Flame gas fired combination unit offers endless hot water and space heating in one extremely efficient unit while fitting into a small footprint, saving on energy, space and cost.

As the second unit to be added to HTP’s Versa-Series, the Versa-Flame incorporates the most revolutionary elements of today’s heating technology with Hydronic mass stabilization. Utilizing high thermal mass the Versa-Flame has the highest first hour output found in the market today, reaching 288 gallons for the first hour delivery.

The unique thermal mass design can only be found in HTP’s innovative Versa-Flame. Stored energy allows the unit to avoid a common issue found in tankless units where domestic hot water flow is interrupted by cold water flow. The Versa-Flame can handle more domestic hot water loads than any other combination platform.

Featuring a unique single loop design with low pressure drop the Versa-Flame eliminates the need for primary secondary circulation for space heating applications, which makes this unit inexpensive and easy to install, saving both the contractor and the homeowner.

Incorporating two heat exchangers for domestic hot water and space heating, the Versa-Flame is a fully modulating unit with an internal PI controller monitoring system conditions to meet demands while operating at a five to one turndown rating. With negative regulation technology the unit induces just the right amount of gas through the valve to mix with fresh air intake, being sure not to use more energy than necessary.

With unique high efficiency space heating attributes, HTP’s proprietary heat exchanger is surrounded by 55 gallons of thermal mass held inside of a stainless steel tank. Thermal mass allows the unit to operate at high efficiencies by reducing unnecessary cycling while avoiding “flashing” which is a common concern found in tankless units. This advancement in technology allows the unit to handle smaller heating loads by reducing short cycling and energy waste.

When a demand for domestic hot water is initialized, heat is pulled from inside of the tank and fed through a brazed plate heat exchanger located at the top of the unit. At 4.8 gallons per minute at a 77 degree temperature rise, the Versa-Flame out performs any competitive combination unit with the ability to simultaneously handle multiple calls for domestic hot water at one time with optimal comfort and efficiency.

The Versa-Flame is offered in three different model sizes offering a great range of availability suitable for residential and smaller commercial needs with the ability to daisy chain up to eight units. After 35 years in the heating industry HTP continues to test the limits of the heating industry by constantly re-inventing the field with high efficient products that offer cost and energy savings.

Thursday, October 13, 2011

Non-Vacuum Vents For Steam Systems

Quick, uniform distribution of heat to all radiation is the first essential to perfect performance. This requires balancing the radiation by controlled venting. Vent-Rite #1 Non-Vacuum vents are adjustable and all vents are designed for positive action and straightline venting. They function automatically to vent the air. If, through an unusual condition, the vent is filled with water, the vent port automatically closes. Vent-Rite has been supplying high quality steam and hot water air valves to home owners, public buildings, institutions and industry for over fifty years and continues to enjoy a reputation for reliability and excellence.

All Vent-Rite valves are made in the USA.




Learn more here.

Thursday, October 6, 2011

Raychem Pipe Freezing Protection

Industrial pipe freeze protection systems are intended to prevent the freezing of fluids in pipes. Raychem electrical pipe freeze protection systems are designed for a variety of industrial applications and environments, including hazardous, non-hazardous, and steam cleanable.

A complete electrical heat-tracing system is much more than just the heating cable. Raychem can provide a complete system from electrical transformer and heat-trace panel to power connection, heating cable, end termination, glass tape and warning labels. We can supply the individual components, provide engineering and design and even install and maintain the entire system.

Electric heating cables are used to maintain temperature of non-flowing fluids by replacing the heat lost through thermal insulation on pipes, vessels and associated equipment.



Learn more here.